MULTIQUIP TP24 Specifikace stáhnout pdf (Strana 25)

TP24 TILE SAW • OPERATION AND PARTS MANUAL — REV. #2 (04/12/12) — PAGE 25

MAINTENANCE

MAINTENANCE INTERVALS

Use the following guidelines to perform maintenance on

your saw.

After every use of the machine

 Remove dirty water from container.

 Remove dirt and mud from the bottom of the container.

 Rinse the immersion pump with fresh water to prevent

water pump clogging from residual dirt.

After wet cleaning and before using the machine

again

 Connect the machine to an electric power outlet

equipped with a “GFCI” safety power breaker. If the safety

power breaker cuts off the electrical power supply, do

not try to operate the machine but have it checked by

an authorized dealer ﬁrst.

Before not using the machine for a prolonged

period of time

 Clean and lubricate all movable parts. DO NOT grease

guide rails.

After not using the machine for a prolonged period

of time

 Check that the stand is safely ﬁxed.

 Check that all screw joints and nuts are ﬁxed.

 Check that the cutting table is seated properly on the

guide rails and that it easily moves along the entire

length of the rails.

 With the saw blade removed, switch on the motor for an

instant and switch it off again. If the motor does not run,

have the machine inspected by a qualiﬁed electrician.

 Check that the immersion pump works properly. Turn

on the cooling water tap and switch the machine on. If

the pump does not give any water or only a little, switch

the machine off at once. Clean the pump, or replace if

necessary.

Ambient temperature below 32°F / 0°C (operation

in winter)

 To prevent the water in the pump and cooling system

from freezing, remove the water after using the machine

or when there will be a long break. Make sure that the

cooling system is entirely drained so that there is no

water left inside the pump and water hose.

CLEANING THE WATER TRAY

Refer to Figure 17.

1. Remove the rear drip tray.

2. Lift the saw up from inside the water tray.

3. Remove the drain plug and drain any water left inside

the water tray.

4. Flush water into tray while holding it upright to remove

any sludge buildup.

5. Replace the saw back into the water tray.

6. Attach the rear drip tray.

Figure 17. Water Tray Removal

1 2 ... 20 21 22 23 24 25 26 27 28 29 30 ... 53 54

Komentáře k této Příručce

Žádné komentáře

Agfa sensor 510-X Specifications (118 pages)

Brand: Agfa | Category: Bridge cameras | Size: 1.56 MB |

English

Table of contents

Classic E.O.S

1

Table of contents

3

❑ Safety precautions

5

❑ Safety compliance

5

Welcome to the Classic E.O.S

6

Safety precautions

7

Safety compliance

9

1280C GB 20001204

10

Getting started with

11

Main components

12

OVERHEAT PROTECTION

13

FIX DEV

13

1 2 3 4 5 6 7 8

14

The control panel

15

Control panel display

16

User language

16

Audio signals

16

Before switching on

17

After switching on

19

Before switching off

20

Switching off

20

Processing films

21

3OHDVHZDLW

23

5($'<

23

53 d&

23

Processing narrow films

24

Processing an emergency film

25

(PHUJHQF\ILOP

26

Recommended chemicals

27

Customization

29

Overview

30

Menu structure diagram

31

0HQXLWHP Æ

32

0HQXLWHP Ç

32

0HQXLWHP

32

9DOXH ÇÆ

32

Processing cycle

34

Developer temperature

36

Dryer setting

38

Setting the dryer setting

39

Developer replenishment rate

40

Fixer replenishment rate

43

(jog cycle)

45

Language

49

Autofill

50

Preventive maintenance

51

General cleaning directions

53

4 Wipe the feed table dry

55

1 Remove the top cover

56

5 Wipe the tank covers dry

57

8 Lock the tank covers

58

9 Reinstall the top cover

58

(*) 2-spring bearing

59

16 Lock the tank covers

65

17 Reinstall the top cover

65

Clean the squeegee roller set

66

7 Reinstall the top cover

67

Clean the pumps

68

8 Reinstall the top cover

71

Troubleshooting

73

Troubleshooting checklist

74

Emergency film processing

75

Maintenance message

76

'HYHORSHU

79

OHYHOORZ

79

11 Lock the tank covers

83

12 Reinstall the top cover

83

The water level is too low

84

Jammed film

85

Film quality problems

87

(UURU

88

6HHPDQXDO

88

3 Reinstall the top cover

89

2 Remove the top cover

90

(UURU

90

4 Reinstall the top cover

91

Developer replenishment tank

92

Fixer replenishment tank

93

Anti-algae accessory

94

E.O.S. Fix

94

Instructions for

95

Important safety notice

96

Clean the dryer roller sets

97

Failure of the dryer heaters

101

3 Remove the cover

102

7 Replace the roller set

103

Cleaning the water filter

104

Equipment information sheet

107

Specifications

108

Physical emissions

111

End of Life

111

Accessories

112

Appendix

113

Printed in Belgium

118

Agfa sensor 510-X User Manual (33 pages)

Brand: Agfa | Category: Bridge cameras | Size: 1.74 MB |

English

Table of contents

SCAN DR SYSTEM

1

Contents

2

Introduction to JSB

3

Composition of DR System

4

Conclusion of JSB

4

II. Digital Radiography (DR)

5

1. Operation of Scan DR

7

High Quality

8

IV. Advantages of JSB Scan DR

10

▶ Scattered radiation

11

CR DDR Inventor-V

13

JSB Medics Co., Ltd

14

DDR Inventor-V

16

334 sec

17

CR Scan DR

19

Image processing

20

1. Action of detector

20

2. DQE of JSB detector

21

High fill factor

22

Detector

23

System Design

23

5. Specifications

24

DDR Inventor

25

Scan-DRM

26

Reference sites

27

Technology

29

Competitiveness

29

VIII. Marketing Survey

31

Effect of Heart beating…

32

THANK YOU

33

More products and manuals for Bridge cameras AGFA

Models	Document Type
Silette	User Manual SILETTE·LK, 26 pages
ePhoto CL 30 Clik!	User's Guide AGFA ePhoto CL 30 Clik! User`s guide, 49 pages
DC-733s	User Manual DC-733s, 2 pages