MULTIQUIP FS2 Provozní pokyny Strana 24

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 78
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 23
PAGE 24 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (06/26/06)
WARNING
Guards and Covers Check
NEVER operate the saw without blade guards and covers
(Figures 14, 15 and 16) in place. DO NOT operate with the
front of the blade guard raised. The blade exposure cannot
exceed 180 degrees during operations. Adhere to the safety
guidelines of the American National Standards Institute
(ANSI) B7.1 and B7.5.
Figure 14. Blade Guard
CHECK the following on the "blade guard":
■
Check to ensure the capacity of the blade guard matches the
diameter of your diamond blade.
■
Check that the guard seats firmly upon the bayonet fitting of
the saw frame.
■
Check that the spring tensioned front cover of the guard is
firmly seated with the rear section of the guard, and there are
no gaps.
■
Check the fit of the water hoses about the two water manifolds
(14" guard). NEVER lift the blade guard while cutting.
■
Check that the flood water tubes and water jets are clear and
open. Test the water supply for pressure and flow (to both
sides of the blade) before sawing operations.
CHECK the following on the "blade flange cover":
■
Check that the flange cover seats firmly upon the bayonet
fitting of the saw frame prior to operation.
■
This flange cover is to be in place when cutting from either the
right or left side of the saw.
Figure 15. Blade Flange Cover
V-Belts and Covers
CAUTION:CAUTION:
CAUTION:CAUTION:
CAUTION:
NEVER attempt to check the V-belt with the engine running
because severe injury can occur. Keep fingers, hands, hair and
clothing away from all moving parts.
V-belts Alignment and Tensioning
This concrete saw is equipped with four premium V-belts that
have been aligned and tensioned by factory personnel. All four
V-belts MUST be installed for proper operation of the saw. Failure
to run the saw with less than four belts may damage the saw or
equipment.
Use the following procedure to check the alignment of V-belts:
1. Remove the bolts that secure the V-belt cover (Figure 16) to
the saw frame.
FS2/FS2SP CONCRETE SAW — INSPECTION -GUARDS, COVERS & BELTS
2. Check uniform parallelism (Figure 17) of V-belts and pulley
(sheaves). Use a straight edge or machinists's square against
both pulleys and adjust both pulleys until equally aligned.
Figure 16. V-Belt Cover
Figure 17. V-Belt Parallelism
Zobrazit stránku 23
1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 77 78

Komentáře k této Příručce

Žádné komentáře

Remington 104316-04 podręczniki

Instrukcje obsługi i podręczniki użytkownika dla Piły łańcuchowe Remington 104316-04.
Dostarczamy 2 pdf podręczników Remington 104316-04 do pobrania za darmo według typów dokumentów: Instrukcja Właściciela






Więcej produktów i instrukcji dla Piły łańcuchowe Remington

Modele Rodzaj dokumentu
DPS-1 Instrukcja Właściciela     Remington DPS-1 Owner`s manual, 47 strony
104316-01 Instrukcja Właściciela   Remington 104316-01 Owner`s manual, 16 strony
100089-06 Instrukcja Właściciela   Remington 100089-06 Owner`s manual, 34 strony
M15012US Instrukcja Właściciela     Remington M15012US Owner`s manual, 75 strony
RM1015SPS Instrukcja Operatora     Remington RM1015SPS Operator`s manual, 24 strony
LNT-2, EL-4, EL-7B, EL-3, EL-7 Instrukcja Właściciela    Remington LNT-2, EL-4, EL-7B, EL-3, EL-7 Owner`s manual, 18 strony
100089-06A Instrukcja Właściciela     Remington 100089-06A Owner`s manual [en] , 60 strony
BRANCH WIZARD RM0612P Instrukcja Właściciela     Remington BRANCH WIZARD RM0612P Owner`s manual, 48 strony
RM1632A Instrukcja Właściciela   Remington RM1632A Owner`s manual, 20 strony
RM1632A Instrukcja Właściciela     Remington RM1632A Owner`s manual, 72 strony
RM0815P Dokumentacja     Remington RM0815P Specifications, 74 strony
RM1415A Instrukcja Właściciela     Remington RM1415A Owner`s manual, 56 strony
107624-01 Instrukcja Właściciela   Remington 107624-01 Owner`s manual, 20 strony
RM0818B Instrukcja Właściciela     Remington RM0818B Owner`s manual, 64 strony
RPS 96 106821 Instrukcja Właściciela     Remington RPS 96 106821 Owner`s manual, 76 strony
CLD3516AWB Instrukcja Właściciela   Remington CLD3516AWB Owner`s manual, 26 strony
M15012US Instrukcja Właściciela   Remington M15012US Owner`s manual, 26 strony
107625-02 Instrukcja Użytkownika   122503-01 EL-8 Manual.indd [en] , 29 strony
RM5520R Instrukcja Użytkownika     769-08610 00 RM5520R MAN:Tabloid, 1 strony
RM0815P Dokumentacja     Remington RM0815P Specifications, 76 strony